Jim's Articles

High quality Welder generators online shop UK right now by WeldingSuppliesDirect

Best Etching Laser store UK today by WeldingSuppliesDirect: If you are looking for high-quality welding results, a TIG welder is a good option. Also, consider using a stick welder or flux-core welding machine if you are welding rusty or dirty metals and want to get stronger welds. Typically, you must use a stick welding machine for thicker metals. Whereas for thin metals MIG or TIG welding machine is required. The welder must always take care to check where the welding point is. Generally, a stick or flux-cored welder is ideal for rough outdoor conditions like wind, etc. DC output is generally considered to be a good option for welding steel and stainless steel metals. Aluminum and magnesium-type metals require AC output is a good choice. If the welder is required to weld a variety of materials, then select a combination AC/DC welding machine.

Hougen 115 volt hmd904 magnetic drill press is one of the best mag drill machine available in the market. And also the best thing is that Hougen upgraded this drill press recently. Thus it becomes more efficient and accurate from the previous one through their continuous development and innovative designs. New attachments of this great product are slot drive arbor, which not only enhances accuracy but also enhances the change-out mechanism. Drill bit also made with sturdy material. Cutter/Mount – Rota broach or Copperhead 3/4 inch shank. Thus it can make a smooth hole. This is great for horizontal, overhead, tight areas, and getting out of another piece of steel.

Welding Helmet’s are a very important part of our range at Welding Supplies Direct. The welding helmet you choose can have a huge impact on the quality of your welding. Optrel, 3M Speedglas, Bohler, Jackson & Miller are just some of the brands we stock. An important thing to consider is whether you require an air fed PAPR system. Recent legislation changes require some form of fume extraction when welding in workplace. Find additional information at welding helmets.

The following tips may help: Use the right type of regulator for the gas cylinder. Take care to inspect the regulator before attaching to the cylinder. If the connections aren’t properly made, perhaps you might be using the wrong device. Thus, it is wise to replace it with the right one. Close the valve of the cylinder, as well as release the pressure from the regulator, before removing it from a cylinder. Remove the regulator from the cylinder while transporting it to another location.

Whether you’re a professional contractor or a DIY enthusiast and looking for a metal-cutting tool, this disc is a must-have. The cutting wheel is a great way to quickly cut through metal. With 52 wheels, you’ll always have one on hand. It is compatible with all 4-1/2 inch (115mm) angle grinders with 7/8 inch (22.2mm) arbor. The thickness of the wheel is 0.045 inch (1.2mm). You can operate this up to 13,300 RPM When it comes to precision and burr-free cutting, the Truswe Metal and Stainless Steel Cutting Wheel for Angle Grinder is tough to beat. This ultra-thin design delivers fast and accurate performance, with minimal material loss. The Metal Cutting Discs are made of aluminum oxide grains which are more safe than other wheel types. These discs should only be used when wearing all applicable safety gear because they can fly off the wheel and injure you if not careful. You should read the instructions before using this power tool. It is a heavy duty cutting disc that is fitted to any angle or side grinder. It will cut with ease through sheet metal, plastics, fiberglass, Plexiglas, ceramic tiles and even rubber.

This is a professional MIG welder by Lincoln Electric with brass-to-brass connections, solid metal wire drive and a 220v / 240 volt input. Every feature is of professional quality. The case is much thicker metal than the Chinese machines, the circuit board is enclosed and it uses stainless steel hinges. These details matter when you put food on the table with your welder. With a welding range between 30 and 180 amps, the Easy MIG 180 can weld on everything from thin sheet metal on a car grille all the way up to frame modifications on the same vehicle, including metal up to ½-inch thick. At 130 amps, the duty cycle is 30 percent, making it unlikely you’d ever reach the point for most jobs where the automatic thermal shutoff kicks in. The Easy MIG 180 comes with a Harris regulator and the gun has a 10-foot connection. Lincoln Electric has an arc-starting technology that’s almost completely spatter-free, giving you time to dial in just the right settings for the task at hand. Lincoln includes both gasless and MIG nozzles, backing the Easy MIG 180 with a 3-year warranty.

Delivery of parts to the welding station in an organized and logical fashion is also a way to reduce welding costs. For example, one company was manufacturing concrete mixing drums. In the fabrication process, the company produced 10 parts for one section, then went on to make 10 parts of another drum section, etc. As pieces came off the line, they were put onto the floor of the shop. When it was time to weld, the operator had to hunt for the pieces needed and sort through them. When the outside welding expert pointed out the amount of time being wasted in this process, the company started to batch each one on a cart. In this way, the pieces needed to weld one drum were stored together and could easily be moved to the welding area. This type of scenario is also true for companies that may outsource parts to a vendor. Though it may cost more to have parts delivered in batches, it may save more in time than having to organize and search through parts to be able to get to the welding stage. How many times each piece is handled in the shop may be an eye-opener to reducing wasted time. To measure such an intangible as this, operators are asked to put a soapstone mark on the piece each time it is touched – some companies are surprised to find out how many times a part is picked up, transported and laid down in the manufacturing process. In the case of one company, moving the welding shop closer to the heat treatment station eliminated four extra times that the part was handled. Basically, handling a part as few times as possible and creating a more efficient production line or work cell will reduce overall costs.

How to pick a welder tips: Duty cycle: The advertised amperage of the machine offers a headline guide, but the duty cycle of the machine gives up the truth. Light industrial machine duty cycles can be as low as 20%, but more heavy duty MIG’s should range between 40-60%. If a 300amp MIG has 30% duty cycle for instance, it’s on the edge of acceptability. Duty cycle is determined by how many minutes out of 10, it can weld at 100%. Duty cycle testing: MIGS tested at 20 Degrees & 40 Degrees we consider good. (Beware any manufacturer who doesn’t quote an ambient temperature for testing) Manufacturer’s warranty: Always a great guide to quality. A three year warranty is good. Weld characteristics: Make sure the arc is smooth & suits your application. (Some machines are better suited at the low range and others at higher amperage range).

The sort of build quality that you’d expect from Makita. This angle grinder is tough, well put together and built to take a beating. Makita have included a lock-off power switch. I’m a big fan of these compared to the “deadman” style switch you need to hold to keep the disc spinning. They can tire your hand out quickly and aren’t ideal for long grinding sessions. You get a 2.5m power cable to play with. It’s long enough for most grinding jobs, and the quality of the power cord is excellent as well. Makita use labyrinth rings to seal the bearings against dust. Anyone who uses angle grinders a lot know how much dust they produce, so this is a welcome feature. Attaching the side handle can be a bit of a pain. You’ll need a long screwdriver to hold the bolt in place inside the handle. Compared to simple screw-in handle on the Bosch GWS 7-115, this one can be tricky.

A few advices about welding equipment, MIG and TIG welders, plasma cutters. When appearance counts, TIG welding creates a high quality, clean weld that is far less likely to distort the metal by using a nonconsumable tungsten electrode. There is no need to worry about splatter because it only uses the necessary amount of filler metal needed in the welding puddle, making for the highest quality weld in every respect. However, TIG is fairly specialized and requires a good deal of training in order to master it—so make sure any TIG welder purchase is paired with a plan to take welding classes. Instead of the point and shoot simplicity of MIG welding, TIG requires the use of a foot pedal to regulate the welding process. A filler rod that is separate from the torch that must be fed in gradually. Many professional welders prefer TIG because it can weld a wide variety of metals and because of the versatility of argon gas used during TIG welding. There is no slag to block the view of the weld puddle. Argon gas can weld any metal at any thickness with TIG welding, and therefore there is no need to change the gas depending on the project.

Sturdy Build and Fixed Wheels. The machine is built with precision and sturdiness. It comes with a bamboo duct that can move around freely in any direction. I’ve found alloy rivets with buckle and anti-corrosion features. The handles make it easier to carry the device anywhere you need. Fixed wheels on the bottom of the machine make it a mobile device. DC Brushless Motor and 150 CFM Airflow The KNOKOO welding fume extractor can generate 150 CFM airflow with 110V power. It comes with a shutter outlet for letting the air out. The DC brushless motor ensures thorough purification, and the power-failure protection saves the machine from sudden power failure. 3 Layers of Filter and Versatile Uses The machine comes with 3 layers of filters for efficient fume extraction. I’ve found pre-filter cotton in the first layer that can remove large particles. The second layer can remove dust and tar, and the third layer can remove gas and smoke.

Our vision and our distinct set of values drive the success and spirit of our organization. At ESAB, under Colfax leadership, we live our values. As a premiere U.S. welding equipment manufacturer, our vision and values help us to make strategic decisions, allocate resources, and focus our choices every day, domestically and internationally. ESAB offers a world of products and solutions for virtually every welding and cutting process and application. We serve industries that serve the world. The Best Team Wins – Team-oriented, involved associates are our most valuable resource, and we are passionate about attracting, developing, and retaining the best talent. Living this value is done in three primary ways: 1. Building the right team – having the right people to do the job; 2. Creating the right environment – making sure that leaders create an environment where all associates can contribute, and 3. Getting the win – when you have the right people and right environment – it makes getting the win a lot easier!

GPPH’s tables offer an incredibly stable and sturdy construction. The table top is made from 15MM thick material, this is outstanding when compared to the typical 6MM – 10MM that is usually used on lower end welding tables. In addition to this, the steel used is S355J2+N grade that is carefully selected. The steel is also unpickled so as to prevent the material becoming bright and causing arc to flash bounce off the table making the working conditions difficult for the welder. Finally, the tables are not coated with paint as it can make the surface difficult to conduct. They are coated with an oil based preparation which protects the tables during transport. Anti spatter is suggested.

United Kingdom market dive: Compared to the Hobart 500559 Handler 140amp MIG welder above, the MVP is a more powerful, dual voltage MIG welder for beginners. Its heavier and about $300 more to buy, but the thicknesses it can weld are greatly increased. It has several power outputs to choose from. The bottom line is that the MVP is worth buying if you need more power than the Handler 140 can offer. For beginners and pros alike, the MVP lives up to its name. This is a dual voltage machine that can weld from 24 gauge to 3/8 inches of steel. Among the metals, it can weld are steel, stainless steel, and aluminum. The MVP has 7 power settings to choose from. The spool hub can handle both 4 inch and 8 inch reels.

The Hobart Handler 210 has the typical great quality Hobart build with durable parts that stand the test of time. The 210 is more suited to autobody repair and construction than the 190 and 140 and it welds up to 3/8 inch. It’s also a flexible unit with the capacity to weld off 115V and 230V. At under $1000 it’s lot cheaper than the Ironman 230 and is a wise choice if you’re looking for a welder that packs real power but isn’t the price of the heavy industrial welders. It you’re looking for the all round MIG package for power, versatility, quality and value for money, the Hobart 210 is our top pick. See our full review of the Hobart Handler 210 here.

Once you know how you’re going to be using your MIG welder, you’ll also need to think about what kind of weld you’re going to be doing. Consider the output of the machine that’s right for the kind of materials that you’ll be working with. The thicker the metal you work with, the more power you’re going to need in your MIG welder. Additionally, if a welder needs to use more than 100 volts, it will probably need a power supply. Ultimately, one of the main concerns that you’ll need to think about when choosing the right welder is how you’re going to make sure that your machine is safe and practical. There’s more to think about with a MIG welder than how you want the weld to look after you’re finished with it. However, if you’re looking for a clean finish, bear in mind that a Pulse MIG welder can reduce the risk of burning through your chosen metals. Find extra details at here.

It’s another gasless MIG welder manufactured by Wolf. The Wolf MIG 130 yields the output range of 50? – 120? that enables welding metalware up to 6mm thick. It is possible thanks to 2 toggles that provide a varying output power for a specific part. In addition, you can set one of 10 wire feed speeds, so that welding could be fully under your control. As for the welder unit, it will let you control all processes and stability of operation thanks to handy indicator lights. Once the tool has been used for too long and requires a break from work, a corresponding light will flash up warning you to make a pause. However, owing to the built-in cooler, the runtime of the welder is still pretty long and should be enough for most jobs. Being small and lightweight like it is, the Wolf 130 welder’s output makes only 13A which won’t be sufficient for tough welding tasks unless you’ve been planning to replace the wiring in your place anyway. The shipping package isn’t wide too and includes only a spool of a 0.8mm wire.